If you are interested how to install the Rival Front Bumper, aluminum 2D.5719.1 for Toyota Land Cruiser 200. Best Ride provides you with complete instructions how to install the product, so that you or your mechanic can follow the appropriate steps.
CAUTION !
To reduce the risk of serious injury or damage , please read and understand all instructions and procedures before attempting to install or use this product . Safety glasses must be worn at all times during installation or maintenance of this product . Ensure all mounting bolts are tensioned after 1000 kms and periodically there after.
NOTICE!
Whilst the bumper adds additional protection to your vehicle , precautionary measures still need to be taken to avoid damage . Always drive to the conditions and your surroundings . ADR69 COMPATIBLE AIR BAG COMPLIANT
- ADR69 COMPATIBLE
- AIR BAG COMPLIANT
SAFETY NOTICE!
- The RIVAL Bumper is designed to compliment the use and design of the specified vehicle under conditions specified by the car manufacturer.
- While driving the vehicle at any speed , collision with any other vehicle , animal or object must always be avoided.
- Following any collision with any other vehicle , animal or object , the RIVAL Bumper and the vehicle must be inspected by a specialized or suitably qualified vehicle repairer for possible damage to the components and assemblies in order to confirm suitability for further use of the vehicle.
- It is strongly recommended that you do not operate a vehicle with a damaged bumper or its components . In the case of damage , please contact the nearest RIVAL dealer.
- The operation of a vehicle where the bumper is not properly attached and fastened to the vehicle , or where the bumper has been damaged , is extremely dangerous and must be avoided at all cost.
- It is recommended that you carry out regular inspections of all the bumper elements such as all bolts , wires , connectors.
INSTALLATION NOTICE
- The RIVAL Bumper must be mounted and affixed to the vehicle according to this installation manual .
- Personal safety during the installation process must be adhered to at all times and the use of personal safety equipment is highly recommended.
REQUIRED TOOLS
- Basic tool kit
- Electric drill
- Angle grinder
- Drill set Torque wrench
- Box knife
- Marker
TORQUE SETTING
- M6 – 9 Nm
- M10 – 44 Nm
* ADR69 AND AIR BAG SYSTEM
The RIVAL Bumper has been tested and certified to be compatible with ADR69 and will not affect the operation of the Air bag System on this vehicle . This product or mounting brackets must not be modified in any way , and must be fitted in accordance with the installation instructions.
TECHNICAL INFORMATION
WINCH INSTALLATION
A winch with a pull capacity of up to 12000 lb can be installed with the RIVAL Bumper . It is not advisable to exceed this pulling capacity since damage , injury or death may occur where the 12000lb recommended capacity is exceeded . There is a special license plate holder supplied with the bumper which will provide access to the winch.
Winch measurements :
Compatible with LED size below :
PARTS LISTING
- Aluminum bumper body – 1 pc.
- Winch bracket – 1 pc.
- License plate – 1 pc.
- LED brackets – 2 pc.
- Flap right- 1 pc.
- Flap left – 1 pc.
- Lower bracket – 2 pc.
- Grille bracket left – 1 pc.
- Grille bracket right – 1 pc.
- Bolt M10x30 – 12 pc.
- Screw M6x16 – 8 pc.
- Screw M6x20 – 23 pc.
- Screw M10x30 – 4 pc.
- Caged nut M6 – 18 pc.
- Nut M6 – 5 pc.
- Nut M10 – 16 buc.
- Washer 6 – 16 buc.
- Washer 10 – 28 buc.
- Countersunk washer – 4 pc.
- LED plug – 2 pc.
INSTALLATION PROCEDURE
1. Open the hood and disconnect terminal ” – ” from the vehicle battery.
2. Remove the plastic pad clip. Dismantle the clip . * Set aside for re – use later on .
3. Remove LED plastic covers.
4. Remove grill connectors.
5. Remove upper grille retaining screws.
6. Remove grille from bumper by carefully releasing locking tabs whilst removing.
7. Remove 3 screws retaining bumper along inside edge of wheel arches on each side of the vehicle.
8. Remove lower bumper retaining screws.
9. Remove 2 bumper retaining screws out of middle part of the bumper.
10. Unscrew 2 screws on the sides of the bumper.
11. Remove all clips , holding bumper with body , under the grill.
12. Disconnect all the cables from the bumper and washer hose , clamp off the washer hose before , to prevent leak of liquid.
13. Carefully remove bumper from vehicle by pulling on each side of the bumper near the wheel arches .
14. Remove damper.
15. Unscrew 3 screws on each side and remove beam.
16. Unscrew 4 nuts on each side of the beam brackets and remove them.
17. Unscrew 2 bolts and remove towing eye on each side.
18. Unscrew 2 screws and remove plastic side fittings on each side.
19. Unscrew fitting screws of the deflector and remove it.
20. Mount winch bracket . Use OE nuts.
21. Install lower brackets on each side . Fix brackets using OE bolts of towing eyes to winch bracket using M10x35 bolts , M10 nuts and washers 10 . Tighten all screw joints .
22. Install LED washers if needed . Strike out plugs from bumper facing and fix LED washers.
23. Install parking sensors if needed . Strike out plugs from bumper facing , fix parking sensors and connect wires.
24. Install bumper body onto the winch bracket . Fix it using 8 bolts M10x35 , 4 screws M10x35 , 4 countersunk washer , nuts M10 and washers 10.
25. Instal caged nuts onto the flaps .
26. Install flaps using screws M6x20 onto the bumper facing on each side.
27. Push flap to plastic fender and mark cutting line . Cut plastic fender following the marked cutting line using jig – saw or shears.
28. Mark and drill 3 holes in plastic fender in accordance with holes in flap on each side of the vehicle . Fix flaps and fenders using screws M6x20.
30. Mount radiator grill and fix it using OE fittings in the upper part and screws M6x20 in the lower part.
31. Install LED plastic covers in reverse order.
32. Connect all the connections and check it . Install plastic pad in reverse order . Connect terminal ” – ” of the battery .
Before operating a vehicle fitted with a RIVAL Bumper :
- make sure all fittings are tightened
- check all electrical wiring attached to lights
About Rival:
Rival is a premium brand, spread internationally:
- 730 employees;
- 10,000 M2 of storage space;
- 27,000 M2 of production space;
- 30 engineers in the R&D department;
- 2 factories: IATF 16949: 2016, ISO 14001: 2015, ISO 9001: 2015.
- 2 global logistics centers in Bremen Germany and Houston Texas.
In Romania and Bulgaria, Rival products are officially distributed by Best Ride.
The product can be purchased by accessing the following link: How to install Rival Aluminum Front Bar 2D.5719.1 for Toyota Land Cruiser 200